No. RG-30 GLASS
Rectangular 4' x 6' glass backboard shall be ruggedly constructed of the finest materials including 1/2” tempered plate glass. Outer perimeter frame shall be a solid extruded heavy steel “F” section with radiused corners. Glass shall be cushioned in the frame with a shock absorbing vinyl molding between glass and framework. Target and border permanently “fired in” standard 2” width. (Fan shaped same specification). For use with G-30 Goal.

No. RG-20 GLASS
Similar to above except 3’-6” x 6’-0”
For use with G-20 Goal.

No. RP-40 WOOD
Rectangular 4’ x 6’ x 11/2” thick double laminated, U.V. filled (both sides), 45 lb. density particle board. Finish of backboard shall be electron beam cured polymer low gloss white having a scratch resistance of 400 GMS min. (Hoffman test method). Backboard shall have a steel perimeter frame with wrap around corners and finished in flat black enamel. For use with G-40 Goal.

Model 1654 Safedge padding is a closed cell rubber, gray in color, 2” thick with corners mitered for easy installation. May be used with any rectangular backboard. (optional) Padding covers front and back edge of backboard as required by the NCAA.

No. RF-50 FIBERGLASS
Rectangular 4’ x 6’ with two gel-coated fiberglass panels laminated together over a solid 11/8” particle board core. Official International Orange border and target markings inlayed into the face of the backboard. Mounting dimensions interchangeable with standard fan shaped backboards. For use with G-50 Goal.

No. 13RGGA DIRECT GOAL MOUNTING ATTACHMENT
All 1300 series backstops, furnished with glass backboards, shall include Model No. 13RGGA direct goal mounting attachment feature for positive connection of goal to main center support of backstop frame. This greatly reduces stress on glass backboard caused by players grabbing the goal ring. Meets all NCAA and NFSHSA regulations.

NOTE: For series 1200, 1400 and 1600 pipe frame backstops Model No. 12RGGA available. (Specify for inclusion)

G-2000 Safety Reflex Goal
The goal has a built in shock absorber to prevent the flyback action that occurs with other goals. Meets all NCAA and high school specifications. available on all rectangular backboards.

G-4000 High tensile strength alloy steel goal
The high strength alloy steel makes it stronger than most goals. Extra heavy bracing gives additional support. Front mounted goals (shown) available on all rectangular backboards. Rear mounted goals available on all fan shaped backboards.

MODEL 120 ABH ADJUSTABLE HEIGHT ATTACHMENT
Backboard adjustable height attachment operates from floor with detachable hand crank for 8’ to 10’ goal height. Load supporting thrust bearings provide easy operation. (Available for use with all backboards - also available in electric operation.)

MODEL W3 SAFETY WINCH
Safety Winch—Fully enclosed 1000# capacity safety worm gear winch with all gears sealed in gear housing and operating in grease. Cable drum is grooved for even cable wrap. Winch furnished with crank for manual operation. Furnished with 2”x10”x20” mounting board. The end bearings of the winch assembly shall be welded to a 1/4”x6”x18” steel base plate which allows direct attachment to wall eliminating any stress on the mounting board. The unit shall be complete with vacuum formed W3-C cover and W3 SAF-ARM locking device. The SAF-ARM shall allow the unit to be locked while not in operation and insure unit is operated by authorized personnel only. (pad lock not included) Consult factory for additional safety items.

PORTABLE ELECTRIC WINCH OPERATOR
Model 1130 1/2 H.P. 115V high torque motor is compact, lightweight and reversible. Right angle drive is for use with W-3 winch. Not recommended for folding backstops with an attachment height above 25 ft. (See Model 500-B Electric Hoist—recommended for heights above 25 ft.) Furnished with PlugHuggerTM locking device so unit can be locked while not in operation and insure unit is operated by authorized personnel only. Consult factory for additional safety items.

MODEL 500-B ELECTRIC HOIST
3/4 H.P. 115V single phase instant reversible motor. Can be installed wall mounted, inverted or upright. Rotary type limit switch control for both raised and lowered position. Worm gear winch holds load in any position\. Gears are precision machined bronze alloy worm gear and induction hardened and ground steel worm fully enclosed and factory lubricated. Cable drum is grooved for even cable wrap. 115V power source and (3) wires to key control switch required at hoist (by others). Also operates with the Goal Tender wireless remote control unit. (See specifications below) Consult factory for safety alarm systems.

GOAL TENDER™ Wireless Remote Control Unit
The Goal Tender hand-held remote control helps you set-up your gym in a matter of minutes. With just the push of a button, you can independently raise or lower basketball backstops, gym dividers, bleachers, or anything else equipped with an electric hoist and our receiver. The Goal Tender comes factory installed on new equipment or can easily be installed on most existing units.

Goal Tender requires no additional wiring, no key switch and there’s no need for conduit and electrical boxes from the hoist. The hand-size wireless transmitter operates with a 9 volt battery and is synchronized with a receiver that can be preset to operate several different hoists separately or in any simultaneous combination.

Model #GT9 controls up to 9 separate units.
Model #GT27 controls up to 27 separate units.